Support of new hardware
Support the following Controllers:
- NJ101 --[]000 Controller Ver.1.46
- NJ101 --[]020 Controller Ver.1.26
- NJ301 Controller Ver.1.46
- NJ501 1[]00 Controller Ver.1.46
- NJ501 1[]20 Controller Ver.1.26
- NJ501 1[]40 Controller Ver.1.26
- NJ501 40 Controller Ver.1.26
- NJ501 5300 Controller Ver.1.26
- NJ501 R0 Controller Ver.1.46
- NX1P2 Controller Ver.1.46
- NX102 --00 Controller Ver.1.46
- NX102 --20 Controller Ver.1.37
- NX701 Controller Ver.1.26
- NY512 Controller Ver.1.26
- NY532 10 Controller Ver.1.26
- NY532 Z[]00 Controller Ver.1.26
EtherNet/IP Connection Setting supports the following target devices:**:**
- SYSMAC Gateway Rev.4
- Smart Camera F430 F series Rev.2
- Autofocus Multicode Reader V430 F series Rev.2
Improved functions
- Animation settings are available both in the window and the dialog box. User can choose the easier way for them.
- Users can change the size of the animation dialog box so that all the information to be checked is displayed.
Enhanced/Improved functions
CONTROLLER
- Solved the problem that a program download might not be complete in the CPU Units whose project unit version is 1.40 or higher.
- Corrected a wrong description about the procedure for missing ESI file, which is a part of responses to ESI file-related errors shown at opening a project.
- Improved the problem that an online edit took a long time from starting to become active in some cases.
- Solved the problem that the simulation instruction SIM SetVelocity might not run in the range of the ring counter settings for the target axis.
- Solved the problem that in the Execution Time Estimation mode, an estimated task execution time might be substantially different from the task execution time in the actual NX102 Controller.
- Expand the setting range of PDO Communications Timeout Detection Count for the CPU Units whose project unit versions are lower than 1.40.
- Solved the problem that users could not install Omron IODD file downloaded from I I-Web, and the message “Failed to install” was displayed.
SAFETY:
- Solved the problem that uploading a Safety CPU Unit program including a 1S-series Servo Drive (Transfer from Controller) showed a warning message in the Output tab page.
- Solved the problem that the comments on the FBD editor might not switch even if the displayed comment setting was changed.
HMI
- Solved the problem that a variable might not be mapped correctly just after devices were toggled. (With this improvement, the Variable mapping window is automatically closed when devices are toggled.)
- Solved the problem that a project for Soft-NA might not be opened in the Version Control.
- Solved the problem that Sysmac Studio might exit abnormally during an operation with tiled pages on display.
- Solved the problem that the font setting was changed to a project's default if an IAG had different language settings.
- Solved the problem that two Animation dialog might appear at the same time.
- Solved the problem that the font information of the custom keypad might be internally illegal in Runtime version 1.11.or higher.
- Improved the issue that the criteria for build error were too strict.
- Solved the problem that the conditions to link devices automatically were different from device importing and exporting.
- Improved the performance when a user changed the font settings with multiple objects selected.
- Solved the problem that the splitter lines were fixed in the Properties window.
- Solved the problem that functions related to trend graph might cause an error in Soft Soft-NA.
- Solved the problem that the slider might not be shown at the correct initial position in the Simulator and Soft Soft-NA.
- Runtime Solved the problem that updating the Alarm Viewer display might rarely cause an error.
- Runtime Solved the problem that when a user downloaded a project in Sysmac Studio version 1.44, the data log might not be saved.
- Runtime Solved the problem that a screen was not shown when a user started the Operation Log Viewer or the Trouble Shooter after booting up Soft Soft-NA.